Yonico 12404q 4 Bit Vertical Raised Panel Router Bit 1/4-Inch Shank
Description
- This set includes 4 beautiful panel raiser profiles to compliment any stile cabinet door. Shanks are 1/4".
- Create center panels for rail and stile cabinet doors
- Premium C3 micro-grain tungsten carbide blades for a sharper & longer lasting edge
- For use on table mount router only
- Silver induction brazing for maximum strength and durability
- ›See more product details
This set includes 4 beautiful panel raiser profiles to compliment any stile cabinet door. Shanks are 1/4".Highlights:- Create center panels for rail and stile cabinet doors- Premium C3 micro-grain tungsten carbide blades for a sharper & longer lasting edge- For use on table mount router- Silver induction brazing for maximum strength and durability- Smaller diameter allow higher RPMs and usage in lower powered routers- Manufactured with anti-kickback design to help prevent workshop mishapsItem Includes:4 Router Bits In Wooden Storage BoxThere's no need to buy a heavy-duty router to make your own doors. Because of their smaller diameter, vertical panel raising bits require less horsepower and can be run at higher speeds than their horizontal counterparts. A vertical bit takes a much smaller "bite" out of the stock so your router won't get bogged down in the middle of a cut. We offer vertical panel raising bits with 1/2" & 1/4” shanks. Choose the larger shank diameter if your router collet will accept it.
Reviews
B**S
Low quality
Very poor quality. You can actually see the serrations on the edge from the grinding process. Leaves a very poor surface finish. Not that I expected CMT or Whiteside quality at this price, but I really feel these are not worth using at any price. You'll be sanding your life away after using these. I'd return them but I already threw out the box they came in.
E**A
They do what they're supposed!
I like the different profiles, the one thing I think I am a little uncomfortable is that it may not be as sharp as it needs to be such a large cut profile.
D**G
About the same quality as all those other yellow bits out there.
Only used one bit to far. Had to resharpen 3 times over 200 ft of shaping. Decent quality.
J**N
Good at price point
Purchased this for the ogee bead profile. Needed it to run 63 MDF panels. The cost of this entire set was as much as a single bit at other locations. I did purchase with the intention of 1 time use, but after receiving and using the bit I needed I can say they will last much longer. I know chinese carbide is much softer then domestic breeds so I am sure frequent sharpening will be needed, but for someone using these here in there outside of a production setting, you cant go wrong. I can also tell you that these are not good for MDF panels, the direction of the cut chips out the face of the panel. Not necessarily a problem for this particular product itself (I dont think) but probably for all vertical bits. Just wish I had thought of that issue before ordering. Luckily I was able to putty and patch those that chipped beyond sander repair. Also, these are probably best suited for 7/8-1" rail and stiles thickness with 3/4" panels. I had to fudge the panel 1/16" proud in 13/16" frame to fit right without protruding out too much to be noticable. . So if you want flush panels in 3/4" frames shop elsewhere.
L**T
Highly recommended
Very high quality at a much more affordable price. With a horizontal router table these make routing raised panels easier and safer.
J**N
More good stuff
Bought raised panel bit and loved it so I bough these.great price and value
C**.
So so
Spend the extra mkney if u can on a good brand name these cut ok just not very clean
R**M
excellent value
I used the cove cutter on 4 white oak cabinet doors and was very pleased with the results.I have found Yonico cutters do an excellent job and would recommend them to anyone.
I**.
One Star
very dull out of the box... I mean very very dull - stick to freud
Common Questions
Trustpilot
2 weeks ago
1 week ago
